Everest Equipment

Everest Equipment strives to be the industry leader in quality and innovation. Everest combines the performance, ruggedness and longevity of its product lines with its deeply rooted commitment to quality assurance and customer service. Everest utilizes state-of-the-art production and design technologies in a manufacturing facility in Ayer’s Cliff, Quebec. Everest Equipment Co. is also the leading designer and manufacturer of custom underground construction forms in North America for vehicular, water/sewage and hydro-electric tunnels.

If you are looking for Everest replacement parts, visit our Everest parts landing page. If you would like to become the proud owner of some Everest Equipment, fill out a quote request form, and we will get back to you as soon as possible!

EVEREST PARTS LANDING

REQUEST A QUOTE

ONE-WAY SNOWPLOWS

OWSK SERIES

Heavy duty tubular sector.
Attack angle position tube.
Adjustable cast runner shoes.
Standard 1/2″ X 8″ C-1085 blade.
Oscillator bar that adjusts plow articulation to road contour.
Standard hitch pin spacing.
Heavy duty lift chains.
High strength low weight design.
Two compression trip spring assemblies.

OWSK9-TE SERIES

9’ Cleared plowing path.
Trip edge design with four torsion springs.
Adjustable moldboard attack angle.
Standard 1/2” by 8” wide cutting edge.
Heavy duty base angle punched on 8 and 12 inch centers.
Available with hydraulic ram or manual reverse pushframe.
10 Gauge break formed moldboard skinplate.
Six 1/2” x 3-1/2” wide moldboard ribs.
Oscillating drive bar with pinning ears on 30-1/2” centers.

REVERSIBLE SNOWPLOWS

OWRL SERIES

10 gauge steel moldboard.
Brake formed for added strength.
1/4” thick keeper plate.
Compression trip moldboard design.
Adjustable moldboard attack angle.
1/4” thick moldboard ribs.
1/2” thick base angle.
15” intake tapered to 40” discharge height.
AASHO standard cutting edge.
1” diameter pin holes on 30-1/2” centers
Reversible pushframe up 32 degrees to either side of bulldoze position.
Twin 3” bore by 12” double acting reverse cylinders.

OWRS SERIES

Trip moldboard one-way design.
31” high intake height and 55” high discharge.
Reversible moldboard capable of 35 degrees of reverse either side of the bull doze position.
Two 3-1/2” diameter bore by 16” stroke reverse cylinders.
Two point level lift chain arrangement or roller level lift arrangement available.
Ideal for removing snow from turn arounds and dead end streets.
10 gauge break formed moldboard skinplate.
Moldboard and curb shoes are supplied standard.
31” oscillator bar drive ears on 31” centers.
1/2” x 8” C-1085 cutting edge.
Cutting edge backer angle punched on 8” and 12” centers.
Optional carbide cutting edge and carbide moldboard shoes.
Optional mushroom shoes or 10” steel wheel caster assemblies.

RHS BUTTERFLY

Trip moldboard design with 10 gauge brake formed skinplate.
Moldboard reverses 35 degrees either side of the bulldoze position.
Two 3-1/2” diameter bore by 16” stroke reverse cylinders.
Two point level lift chain arrangement or roller level lift arrangement available.
Oscillator bar with 1” flame cut ears on 31” centers.
Ram reverse or worm gear reverse options.
1/2” by 8” C-1085 cutting edge.
Cutting edge backer angle punched on 8” and 12” centers.
Moldboard and curb shoes supplied standard.

RHS SERIES

Trip moldboard design through four heavy duty adjustable tension springs.
Reversible moldboard capable of reversing 35 degrees either side of bulldoze position.
Reversing action provided by two 3-1/2” diameter bore by 16” stroke cylinders.
Two point level lift chain arrangement or roller level lift arrangement available.
10 gauge heavy duty “C” curl moldboard.
Moldboard shoes and curb shoes are standard items.
Oscillator drive bar lugs are on 31” centers.
Ram reverse or worm gear reverse option.
36” or 45” high moldboard curl.
1/2” by 8” C-1085 cutting edge.
Cutting edge backer angle punched on 8” and 12” centers.

RHS VORTEX SERIES

Trip moldboard design.
Nominal 36” high moldboard tapering from the center line of the moldboard to 54” high at the discharge.
Moldboard capable of reversing 35 degrees either side of the bulldoze position.
Two 3-1/2” diameter bore by 16” stroke nitrided reversing cylinders.
Two point level lift chain arrangement or roller level lift arrangement available.
10 gauge brake formed skinplate.
Moldboard and curb shoes supplied standard.
31” Oscillator drive ear centers.
1/2” x 8” C-1085 Cutting edge.
Cutting edge backer angle punched on 8” or 12” centers.

RL SERIES

Trip edge design
30” high moldboard.
Moldboard capable of reversing 30 degrees either side of the bulldoze position.
Two 2-1/2” diameter bore by 16” stroke nitrided reversing cylinders.
Two reversing cylinder pin on locations.
3/8” polymer skinplate.
25” oscillator drive ear centers.
1/2” by 8” C-1085 cutting edge.
Cutting edge backer angle punched on 8” or 12” centers.
6” by 3-1/2” by 5/16” trip edge backer angle reinforcement.

RLHD SERIES

Light weight design.
7 gauge steel moldboard.
Tension trip moldboard design using six (6) 3/8” steel wire tension springs with adjusters.
1/4” thick rib plates.
1/2” by 8” C-1085 steel blade standard.
3” x 3” x 3/8” steel backer angle.
Two rebound bumpers to cushion the moldboard when returning to plowing position after tripping action.
Hydraulic reverse capable of 32 degrees of angling.
Locking pin to set moldboard at 3 different locations.
The plow pins on at 30-1/2” centers.

RM-POLY SERIES

36” high moldboard curl with replacable 3/8” polymer UHMW skinplate.
15 degree blade attack angle with heavy duty trip edge design.
Moldboard reverses 35 degrees either side of bulldoze position.
Hydraulic ram or manual reverse pushframes available.
Two point level lift chain arrangement standard.
Four 3/4” diameter wire by 13” long torsion spring trip edge return system.
Heavy duty backer angle punched to accept 8” and 12” centers cutting edges.
1/2” by 8” C-1085 reversible cutting edge.
The pushframe has a heavy duty 4” x 4” x 3/8” HSS pushbar spanning the three attachment points to the moldboard.
Oscillator bar with 3/4” flame cut ears on 31” centers.

RM-STEEL SERIES

36” high, 10 gauge brake formed moldboard curl.
15 degree blade attack angle with heavy duty trip edge design.
Moldboard reverses 35 degrees either side of bulldoze position.
Hydraulic ram or manual reverse pushframes available.
Two point level lift chain arrangement standard.
Four 3/4” diameter wire by 13” long torsion spring trip edge return system.
Heavy duty backer angle punched to accept 8” and 12” centers cutting edges.
1/2” by 8” C-1085 reversible cutting edge.
Heavy duty pushframe spanning three attachment points to the moldboard.
Oscillator bar with 3/4” flame cut ears on 31” centers.

RMTM SERIES

36” high by 10 feet long with 10 gauge heavy duty curled skinplate.
Trip moldboard design using four 5/8” diameter wire by 3-1/2” O.D. by 22-1/2” long heavy duty adjustable tension springs.
15 degree blade attack angle with heavy duty base angle.
Moldboard is capable of reversing 35 degrees either side of bulldoze position through two 3-1/2” diameter by 12” stroke hydraulic reversing cylinders or manually reversed with lock out pins at preset degrees.
Six 3/8” thick moldboard reinforcement ribs standard.
Heavy duty pushframe 4” x 4” x 3/8” HSS pushbar spanning the three attachment points of the moldboard.
Heavy duty angle oscillator bar with flame cut ears on 31” centers to allow the moldboard to follow the road contours.
Moldboard trip action controlled by a center mount, rubber cushioned, thrust rod which reduces stress during tripping.
Moldboard backer angle punched to accept 12” centers cutting edges
Two point level lift chain arrangement standard.

RTE BUTTERFLY

Trip edge moldboard design with 10 gauge brake formed skinplate, 36” high at center tapering upwards to 54” high at the discharge end.
Moldboard reverses 35 degrees either side of the bulldoze position.
Two 3-1/2” diameter bore by 16” stroke reverse cylinders.
Two point level lift chain arrangement or roller level lift arrangement available.
Oscillator bar with 1” flame cut ears on 31” centers.
Ram reverse or worm gear reverse options.
1/2” by 8” C-1085 cutting edge.
Cutting edge backer angle punched on 8” and 12” centers.
Moldboard shoes and curb shoes supplied standard.

RTE VORTEX

Trip edge moldboard design with 10 gauge brake formed skinplate, 36” high at center tapering upwards to 54” high at the discharge end.
Moldboard reverses 35 degrees either side of the bulldoze position.
Two 3-1/2” diameter bore by 16” stroke reverse cylinders.
Two point level lift chain arrangement or roller level lift arrangement available.
Oscillator bar with 1” flame cut ears on 31” centers.
Ram reverse or worm gear reverse options.
1/2” by 8” C-1085 cutting edge.
Cutting edge backer angle punched on 8” and 12” centers.
Moldboard shoes and curb shoes supplied standard.

RTE-POLY

Reversible moldboard 35 degrees either side of bulldoze position.
Trip edge design plow.
3-1/2” bore x 16” stroke reverse cylinders.
3/8” Polymer UHMW skinplate.
Curb shoes.
31” drive ear centers.
1/2” by 8” blade on 8” and 12” centers punch pattern.
39” or 45” high moldboard curl.
Ram reverse or worm gear reverse kits.

RTE-STEEL

Reversible moldboard 35 degrees either side of bulldoze position.
Trip edge design plow.
3-1/2” bore x 16” stroke reverse cylinders.
10 gauge skinplate.
Curb shoes.
31” drive ear centers.
1/2” by 8” blade on 8” and 12” centers punch pattern.
39” or 45” high moldboard curl.
Ram reverse or worm gear reverse kits.

VRL PLOW

12 gauge steel moldboard.
Brake formed for added strength.
Compression trip moldboard design with rubber impact stops across the lower position of the moldboard.
Adjustable moldboard attack angle.
1/4” thick moldboard ribs. Double ribs at drive points.
1/2” thick base angle.
27” nominal height tapering from the center line of plow to 37” of discharge height.
AASHO standard cutting edge.
1” diameter pin holes on 30-1/2” centers.
Reversible pushframe up 32 degrees to either side of bulldoze position
Twin 3” bore by 12” double acting reverse cylinders.

WINGS AND WING SYSTEMS

ACC-HCC SERIES

Our ACC rear tower incorporates a hydraulic and cable system.
This system allows the wing to be raised into travel position and also used for shelving purposes.
The lift control cylinders are housed in the rear tower so to be shielded from sand and salt and to reduce corrosion.
The tower is constructed from 12″ channel with a 1/4″ enclosed cabinet with access doors to service the hydraulic cylinders.
No portion of the cylinders shall extrude past the top of the tower.
Vertical lift is accomplished through the use of hydraulic cylinders and cable sheaved to reach 36″ or 54″ of travel.
The HCC front tower features a low profile design. This tower design provides adequate wing lift without vertical extensions above the tower structure.
Open tower design is self-cleaning easily shedding snow and road debris.
Lift cylinder is located behind the tower beam for greater protection.
The modular tower attachment brackets provide simple removal to allow for service or off-season weight savings.
If the truck is fitted out with a Power Tilt hitch, this tower will tilt forward with the hitch for ease of truck servicing.
The HCC tower provides 36″ or 72″ of vertical wing lift. This system normally incorporates our safety trip dee for full moldboard trip action.

ACP SERIES

Independently controlled hydraulic front tower with safety trip dee.
Hydraulic cylinder inside enclosed cabinet for protection.
Allows wing 6″ of float.
Slider assembly runs full length of front tower.
Tower tilts forward with power tilt hitch.
The tower bolts to cross tubes.
Totally hydraulic rear tower.
Completely enclosed rear cabinet with hydraulic cylinder located inside for protection.
Tower slider attaches directly to cylinder end for positive lift. Square bar slider keeper track full length of rear tower.
The upper wing arm incorporates a wire tension trip spring to return wing to plowing position after wing has encountered an obstruction.
The upper wing arm has a sliding cylinder connecting lug to lift the wing and also to provide vertical wing float.
The upper arm will extend from 66″ to 78″ in length (pin to pin).
The lower arm incorporates a compression spring to create a shock absorber affect for the wing plow.
The wing arms have universal joint connectors at both ends of the wing arms.
The lower wing arm will extend from 64″ to 76″ (pin to pin).

ACPEA SERIES

Our ACP48 front tower is independently controlled providing 48″ of vertical wing lift. This system incorporates our 30 degree rubber timbren safety trip dee for full moldboard trip action.
The tower’s slider assembly runs full length of the front tower and allows for 6″ of wing float.
The tower bolts to the front hitch support cross tubes.
The modular tower attachment brackets provide simple removal to allow for service or off-season weight savings.
If the truck is fitted out with a Power Tilt hitch, this tower will tilt forward with the hitch for ease of truck servicing.
(This wing system is also available with our ACP36 fully hydraulic front tower).
Our low profile ACPEA patrol rear module minimizes the mounting area required behind the truck cab for installation.
The ACPEA rear module incorporates a hydraulic cylinder to raise and lower the rear of the wing moldboard.
The wing arm mounting structure is designed to be removable through a pull pin device.
The rear assembly incorporates a base basket to reduce the amount of space requested to mount a sander application or standard dump.
The ACPEA is designed with a single telescopic wing arm with a built in compression spring shock absorber. The wing arm has a cylinder mount to the side to allow the wing arm to extend outwards by 21″ to increase the cleared path as needed.
This design also allows for limited shelving capabilities.

ACPF SERIES

The ACPF Patrol cable system is modular for easy installation and removal, and is designed for severe duty applications.
The HCC front tower features a low profile design. This tower design provides adequate wing lift without vertical extensions above the tower structure.
Open tower design is self-cleaning easily shedding snow and road debris.
Lift cylinder is located behind the tower beam for greater protection.
The modular tower attachment brackets provide simple removal to allow for service or off-season weight savings.
Incorporates a safety trip dee for full moldboard trip action.
The low profile ACPF patrol rear module minimizes the mounting area required behind the truck cab for installation and incorporates a hydraulic cylinder to raise and lower the rear of the wing moldboard.
The upper wing arm features a tension spring to assist the tripping action.
The lower wing arm features a compression spring to absorb forces from wing plowing.

ACPFM SERIES

The HCC front tower features a low profile design. This tower design provides adequate wing lift without vertical extensions above the tower structure.
Open tower design is self-cleaning easily shedding snow and road debris.
Lift cylinder is located behind the tower beam for greater protection.
The modular tower attachment brackets provide simple removal to allow for service or off-season weight savings.
If the truck is fitted out with a Power Tilt hitch, this tower will tilt forward with the hitch for ease of truck servicing.
The HCC36 tower provides 36″ of vertical wing lift. This system normally incorporates our safety trip dee for full moldboard trip action.
(This wing system is also available with our ACP36 fully hydraulic front tower).
Our low profile ACPFM patrol rear module minimizes the mounting area required behind the truck cab for installation.
The ACPFM rear module incorporates a hydraulic cylinder to raise and lower the rear of the wing moldboard.
The wing arm mounting structure is made from 6 x 6 HSS section with heavy plate attachment lugs for the wing arms and the lifting cylinder.
The upper wing arm features a tension spring to assist the tripping action.
The lower wing arm features a compression spring to absorb forces from wing plowing.

MID MOUNT SERIES

Mid Mount System and Wing design to improve chassis weight distribution over front and rear axles.
Increased vision of side wing in travel and plowing mode from passenger side mirror.
Wing system design allows for clear view for the driver from all windows of cab during plowing and travel modes.
The side wing has is close and tighter to the chassis in travel mode.
Spring loaded wing arm helps reduce side impact shocks to chassis.
Rear mounted wing lift cylinder for better wing control and holds wing in a ridged position in travel mode.
Front and rear built in wing float mechanism to allow the side wing to follow the road surface.
Heavy duty front 16″ slide wing post with direct lift hydraulic cylinder.
Front mount spring loaded wing trip dee designed to allow the side wing to trip forward to overcome road obstacles in plowing path. Minimizes potential wing and chassis damage.

POLY WING

Bolt on UHMW polymer sheet moldboard design reduces weight.
Wing utilizes a 15 degree attack angle.
Heavy duty wing moldboard frame.
Wing designed to be used on medium and light duty chassis.
Heavy duty base angle construction.
Heavy duty top rail and nose plate.
3/8” thick vertical and horizontal rib plates.
Two 1-1/4” diameter wing nose plate mounting holes.
1/2” by 8” C-1090 cutting edge on 8” centers.

REAR MOUNT SERIES

Heavy Duty rear mount wing for Class 8 trucks.
Offers extremely rugged design to mount cleanly with rear saddle behind the rear wheels.
Allows for tight installation of body to back of cab for improved chassis turning radius.
Available with standard two push arm system with safety trip dee or single push arm system with timbren trip.
Single arm system available with fixed or extendable push arm.
Rear mount system tucks wing tight into side of truck in travel position for improved visibility and cab access over conventional forward wing mounts.

SNO-FIGHTER

Fixed mount rear tower with 36” travel front tower.
60” adjustable wing arms with compression spring on bottom arm to absorb shock.
Hydraulic cylinder raises wing into travel position.
Rear and front tower are removable for summer storage.
10’ polymer ultra light wing.
Wing system features a compression spring trip dee to allow wing to trip over obstructions in plowing path.
Hoses are fitted with quick coupler connections to facilitate removal of equipment for summer use.
The hitch is designed to power tilt forward to allow for a tilt forward cab design.
Accommodates a tailgate spreader.
MSL 9’ body design to hold 3 yards of material.
16” sides and 20” tailgate.
Powered by UBDL1618 hoist.

WING 10°

Break formed moldboard for improved casting.
The 10° attack angle allows for less aggressive scraping action of the plowed surface.
Wing design allows wing to be closer to cab in travel position.
Multiple locations for wing arm mounting bracket.
Heavy duty base angle construction.
Heavy duty top rail and nose plate.
3/8″ Thick vertical and horizontal plate ribs.
Two 1-1/2″ diameter wing nose plate mounting holes.

WING 22°

Paneled 22 ° attack angle moldboard for improved casting.
Multiple locations for wing arm mounting bracket.
Heavy duty base angle construction.
Heavy duty top rail and nose plate.
Two 1-1/2” diameter wing mounting holes.

WING-TE SERIES

Paneled 22 degree attack angle moldboard for improved casting.
Multiple locations for wing arm mounting bracket.
Heavy duty base angle trip edge construction.
Heavy duty top rail and nose plate.
3/8” Thick vertical and horizontal ribs.
Two 1-1/2” diameter wing mounting holes.
Four 3/4” by 3-1/2” diameter torsion springs return blade to plowing position after overcoming an obstruction.

PLOW HITCHES

PT QC-DM

Intended for truck chassis with greater than 35,000 pound gross vehicle weight.
Heavy duty angle, plate, and tube construction for added strength.
The bumper plate is adjustable for varying frame heights.
5/8″ thick cheekplates designed for stress transfer to chassis frame rails.
Hydraulically detachable front mast design permits off-season removal in minutes with upper and lower hydraulic mast locking pins.
Power tilting for tilt forward cab design feature allowing the wing tower tilts with hitch.
Twin 6″ x 4″ x 3/8″ HSS crosstubes for wing tower mounting.
Hitch may also be used without crosstubes for plow mount only.
4″ diameter bore by 10″ stroke double acting nitrided lift ram cylinder providing over 16″ of lift.
Adjustable parking feet to allow for proper mast quick coupling and uncoupling.
Three attach pin heights on 31″ centers. Available adapter kit (not shown) for 21″ centers.

PT SERIES

Intended for truck chassis with greater than 35,000 pound gross vehicle weight.
Pin on design permits off-season removal in minutes.
Heavy duty angle, plate and tube construction for added strength.
5/8″ thick bumper plate is adjustable for varying frame heights.
5/8″ thick cheekplates designed for stress transfer to chassis frame rails.
Power tilting for tilt forward cab design feature.
Wing tower tilts with hitch.
4″ Diameter bore by 14″ stroke double acting nitrided lift ram cylinder providing over 20″ of lift.
Cylinder base angle is reinforced with 5/8″ plate.
Twin 6″ x 4″ x 3/8″ HSS crosstubes for wing tower mounting. Hitch may also be used without crosstubes for plow mount only.
Three attach pin heights on 31″ centers.
Provisions for a front mount pump.
Available adapter kit (not shown) for 21″ centers.

PT QC JUNIOR

Designed to be used with medium duty trucks.
All hydraulic rapid coupling system.
One man operation from cab (if used with reversible plow, plow reverse hoses need to be manually connected and disconnected).
Approach guides help the driver line up the male and female section during coupling.
Female section can be mounted on most plow pushframes produced by major plow manufacturers.
Dual hydraulic cylinders.
Hidden locking cylinder secures pin ears in place.
No pins to wrestle.
Adjustable bolt on plow pushframe attachment ears allows for various plow pushframe heights for added versitility.
The hitch design allows for side wing mounting without modifications to the hitch mast or cheekplate kit.
The hitch mast is designed for easy off, by removing four pins.
Chain hooks for securing the female section to the plow pushframe supplied.
Spring loaded female section support arms ensures proper angling and relief of female section during coupling.

PT QC-M

Tilt kit allows the hitch to tilt forward from the base pin ear location to accommodate forward tilting truck cabs and engine hoods.
Chain hooks for securing female section to plow pushframe supplied.
One man operation from cab (if used with reversible plow, plow reverse hoses need to be manually connected).
All hydraulic rapid coupling system.
Male section lift cylinder 4” bore by 12” stroke double acting nitrided cylinder with 2-1/2” double acting locking cylinder.
5/8” heavy duty cheek plate kit with 5/8” bumper plate ensure good load transfer and carrying for heavy duty use.
Hidden locking cylinder secures pin ears in place.
No pins to wrestle.
Approach guides help the driver line up the male and female section during coupling.
Withstands heavy duty, continuous plowing service.
Female portion can be mounted on most plow push frames produced by major plow manufacturers.

PT-M SERIES

Intended for truck chassis with less than 35,000 GVWR.
Pin on design permits off-season removal in minutes.
Heavy duty angle, plate and tube construction for added strength.
Bumper plate is adjustable for varying frame heights.
Cheekplates designed for stress transfer to chassis frame rails.
Power tilting for tilt forward cab design feature.
Wing tower tilts with hitch.
3” diameter bore by 12” stroke double acting nitrided lift ram cylinder.
Twin 4” x 4” x 3/8” HSS crosstubes for wing tower mounting.
Three attach pin heights on 31” centers.
Provisions for a front mount pump.
Available adapter kit for 21” centers.

LOW MOUNT

Heavy duty low mount hitch for class 8 trucks.
Allows chassis hood with fixed grille to open over top of the hitch with front plow in place.
Double acting pick cylinder with adjustable – extendable nose piece assists with proper level lift of plow.
30-1/2” plow mount centers and several options for quick plow attachments are available.

This is a small overview of the products Everest Equipment has to offer. For a complete selection of their products, and a full list of details, check out Everest‘s website.

EVEREST WEBSITE