This versatile, general purpose full trip plow is best used for municipal, commercial, airport and off road plowing.

Used primarily in metropolitan areas, this sectional trip plow allows you to pass over an immovable object without losing the snow load — only the section hitting the object will trip.

The curve of the moldboard casts the snow downward, reducing damage from thrown snow and avoids covering sidewalks & driveways. Spring tension is adjustable on the J-Style plow, whereas it is not adjustable on the C-Style Torsion Trip Edge.

This versatile, general purpose trip edge plow is best used in situations where the snow casting pattern changes often. The Flex Plow allows you to change the moldboard profile on-the-fly from the truck cab: Right, Center & Left Discharge.

Used in both rural and metropolitan areas, the long, tapered moldboard allows the plow to lift and roll the snow. This plow can also be configured with a reversing table to allow for intersection clean up.

Used in rural areas because the attack angle and depth of the plow throat allow the plow to discharge large amounts of snow. The deeper throat also helps prevent snow from blowing over the top of the plow & onto the truck’s windshield.

This plow is designed for high-speed use in rural paved areas with deep snow.

Primarily used in rural areas, mountain passes, expressways and interstate highways, this plow is designed to discharge snow to the right or to the left, depending on the angle of the plow. Available in full trip or slotted trip.

The Monroe V-Plow provides a 10′ clearing path! Available in two intake/discharge heights:  42″ x 72″ or 56″ x 82″. Various truck hitch attachments to choose from. 

• Single Function Wing is Operated with Single Lever Control for Ease of Operation; Double Function is Operated by Two Hydraulic Function Controls to Independently Control the Heel and Toe End of the Wing Moldboard.
• 100% Welded Moldboard
• 1-Piece 1⁄2” Moldboard Reinforcement Ribs
• Free Float to Follow Contour of Road to Shoulder
• Rear Push Mount Installed Above Frame for Increased Ground to Rear Mount Clearance
• 100% Powder Coat Finish

• 3⁄16” Formed Moldboards.
• 4” x 4” x 3⁄4” Moldboard Bottom Angle.
• 1⁄2” Moldboard Ribs.
• Structural I-Beam, Direct-Lift Front Post with 3-1⁄2” x 62” Lift Cylinder.
• Single Telescoping, Three-Position Adjustable, Spring Cushioned Pusharms with Shear Pins.
• 100% Powder Coated Orange.

• 24” H x 8’ L Moldboard.
• 1⁄2”, Tapered, One-Piece, Flamecut Ribs.
• 5⁄8” x 8” AASHO Top Punched Cutting Edge.
• Wing Provided with Under Frame Cross Tube Mounting and Hardware.
• Wing Requires Two 4-Way Valves & One 3-Way Valve to Operate (Not included).
• Two Double-Acting Cylinders; One Extension Cylinder and One Heel Cylinder.
• One Single Acting Cylinder for Toe.
• Moldboard is Shot Blasted and Powder Coat Painted Orange.
• Mounting Hardware is Powder Coat Painted Black.
• Non-Trip Moldboard.
• 10 Gauge Continuously Welded Moldboard.

• 27” Intake Height and 28” Discharge Height on Moldboard.
• Two Double-Acting Cylinders for Direct Lift of Toe and Heel.
• Direct-Lift Front Wing Post.
• Wing Requires Two 4-Way Valves with 2100 PSI Relief for Heel Raise to Operate (Not included).
• Wing Provided with Under Frame Cross Tube Mounting and Hardware.
• Moldboard is Shot Blasted and Powder Coat Painted Orange.
• Mounting Hardware is Powder Coat Painted Black.
• 10 Gauge Moldboard.
• 3⁄8” One Piece, Tapered, Flame Cut Ribs.

A versatile and inexpensive spreader which allows you to dispense a variety of free-flowing granular materials for the purpose of making roads, driveways, parking lots and runways safe for travel. Available in mild and stainless steel. Model MS969 shown above.  Refer to literature for additional models and options.

A V-box for the small municipality or contractor that does not require a large amount of snow and ice control. This unit is designed for use in pickups, platforms and small dump bodies. Available in mild or stainless steel, hydraulic or electric drive.

A multi-purpose radius body with the ability to be used as a dump body or a spreader. Material can be discharged through the rear tailgate or the forward metering gate onto a spinner assembly or a front cross conveyor.

The Under Tailgate Roll Spreader allows you to drop free-flowing material in an 88″ or 96″ wide path directly behind the truck — critical in areas where users do not want to broadcast material over a wide area. Ideal for spreading abrasives for snow & ice control, chip spreading and seal coating operations.

A Mid-Size V-Box to be used by municipalities or contractors for their granular snow and ice control needs. This unit is designed for use on platforms or small to medium sized dump bodies. Available in mild or stainless steel.

A multi-purpose flat floor body with the ability to be used as a dump body or a spreader. Material can be discharged through the rear tailgate or the front drop chute onto a spinner assembly.

This spreader completely replaces the original dump body tailgate. Each spreader is custom-built to your dump body to ensure a tight fit, no material leakage and excellent spinner clearance. Available in mild or stainless steel on 1-ton and large dump applications.

Modular-design v-box spreader available in single auger, dual auger or conveyor chain discharge. Can be chassis mounted, dump body mounted or skid mounted depending on your needs. Available in mild or stainless steel.

A multi-purpose v-body with the ability to be used as a dump body or a spreader. Material can be discharged through the rear tailgate or the forward metering gate onto a spinner assembly or a front cross conveyor.

The rear cross conveyor is a low-maintenance, self-cleaning unit that is perfect for the small municipality that needs to spread abrasives in the winter and shoulder for spring and summer work. Available in mild or stainless steel with 12″ or 18″ wide conveyor.

This is a chassis mounted v-box with a 34″ wide conveyor with a rear opening tailgate. This allows for a high rate of material discharge. Available in mild or stainless steel.

A multi-purpose dump body with the ability to be used as a dump body or a spreader. By tilting the floor up, material can be discharged through the forward metering gate onto a left-hand front spinner assembly.

Pre-wet salt works faster and at lower temperatures than dry salt, with less waste. Instead of bouncing off the road or being swept away by traffic like dry salt, pre-wetted salt clings to the slippery roadway. Using less salt saves money and is better for the environment. Several systems are available to accommodate your application.

Anti-Icing is a proactive approach to snow & ice control. It is used in areas where liquid chemicals could be applied early enough, prior to precipitation, to prevent snow or ice from bonding on road surfaces. Ultimately, anti-icing makes cleanup quicker, reduces labor hours and reduces wear on snow removal equipment.

Management of vegetation is an important element of roadside maintenance for safety and aesthetics. Carrier Tank capacities are available from as little as 500 Gallons to as much as 3000 Gallons, while Chemical Tanks range from 30 to 85 Gallons. Standard and custom designed systems are available to fit your specific needs.

• 1” Thick Moldboard with Formed Offset for Cutting Edge.
• Moldboard – Length: 10’, 11’ & 12’; Height: 20” or 15”.
• 1/2” x 6”, AASHO Punch, Double Beveled Cutting Edge.
• Reversible 45˚ Left and Right with Infinite Plow Positions.
• (2) 4” x 12” Double Acting Reversing Cylinders with 2” Rods.
• Socatri 1000 Cylinder Rods are Extremely Corrosion Resistant.
• 5” Center Pin Is Piloted into Hangerboard to Increase Effective Surface Area to Relieve Side Shear on the Pivot Bushing.
• Contour Shaped Hold Down Blocks Match the Radius of the Circle for Increased Strength.
• Bolt On Trunion Pins at Canister Pivot Points for Ease of Maintenance and Simpler Replacement.

• Moldboard Length: 10’, 11’ & 12’; Height: 20”.
• Two Piece Moldboard
  • Upper Deflector is 1/2” x 10”
  • Lower Deflector is 3/4” x 9”
• 1” x 10” Hangerboard.
• 1/2” x 6”, AASHO Punch, Double Beveled Cutting Edge.
• (2) 3” Actuating Cylinders.
• 1” Solid Circle.
• 5” Center Pin.
• Two 4” Power Reverse Cylinder.
• (4) Heavy Duty Long Travel Spring Assemblies for Absorbing Road Shock.
• Moldboard Angles up to 45˚.

• 1” Thick Moldboard with Formed Offset for Cutting Edge.
• Fixed Angle Moldboard: Length 10’, 11’ & 12’; Height: 20” or 15”.
• 1/2” x 6” AASHO Punch DBC Cutting Edge.
• Heavy-duty 1/2” Reinforced Hangerboard.
• Dual Canister Trip.
• Heavy-duty Hinge Assembly.
• 3/4” Hanger Plates.

• 1” Thick Moldboard with Formed Offset for Cutting Edge.
• Fixed Angle Moldboard – Length: 10’, 11’ & 12’; Height: 20”.
• 1/2” x 6”, AASHO Punch, Double Beveled Cutting Edge.
• (1) 3” x 11.5” Actuating Cylinder.
• One Shock Absorber.
• Fixed, Right or Left Discharge Angle 35˚-45˚ (Depending on Vehicle Wheelbase).